Every motor delivers torque. That is not the question. The real question is what that motor costs you in space, weight, compliance, and integration effort before it delivers a single newton-meter of useful work.
Traditional housed motors come with a housing, shaft, bearings, endbells, and often a coupling or gearbox. Each of those components consumes space, adds mass, and introduces mechanical weakness.
For applications where every millimeter and every gram counts, those "necessary" parts become liabilities. Frameless motors remove them. But removing parts is not the point — solving the problems those parts create is the point. Let us walk through what those problems actually are.
The Space Problem
A traditional servo motor is a self-contained cylinder. You mount it somewhere on the machine, then run a shaft, belt, or gearbox to connect it to the load. That motor occupies volume that could otherwise hold payload, batteries, or additional functionality.
In robotic joints, this is a critical constraint. A joint has a fixed envelope. Every millimeter of motor length is a millimeter you cannot use for something else. Frameless motors address this by eliminating the housing entirely.
The stator mounts directly into the machine structure, and the rotor attaches directly to the load shaft. The motor becomes part of the structure rather than an appendage to it.
The FMK series frameless torque motors, for example, are designed specifically for this use case. The stator and rotor integrate directly into the joint, with the hollow bore providing routing space for cables, sensors, and fluid lines.
External diameters range from 25 mm to 115 mm, allowing the motor to fit within joint envelopes that would never accommodate a housed motor of equivalent torque.
The Weight Problem
Mass is the enemy of dynamic performance. A heavier motor requires more torque to accelerate, which requires a bigger motor, which adds more mass. This vicious cycle is particularly acute in mobile systems — AGVs, drones, legged robots — where every gram reduces payload capacity or battery life.
A housed motor carries a housing that does nothing but contain the rotor and stator. That housing is dead weight. Frameless motors eliminate it. The rotor and stator are the active electromagnetic elements; everything else is surplus.
Our FMK series uses an optimized stator welding process and rotor manufacturing technique to reduce motor weight while increasing power density. The result is a motor that delivers more torque per kilogram than most housed equivalents.
For a robot with multiple joints, the cumulative weight reduction is substantial — and every gram saved improves acceleration, reduces energy consumption, and extends battery life.
The Stiffness Problem
This is the problem that engineers often overlook until it shows up in the field. A conventional motor connects to the load through a shaft, coupling, and possibly a gearbox or belt drive. Each of those mechanical connections introduces compliance — the system twists slightly under load before the load actually moves.
That compliance reduces system bandwidth, increases settle times, and degrades positioning accuracy. In high-precision applications, the difference between "commanded position" and "actual position" is often the result of mechanical wind-up in the transmission.
When a frameless torque motor is used in a direct-drive architecture, the rotor can connect directly to the load shaft without a gearbox or coupling. This can substantially reduce transmission compliance and eliminate backlash associated with those mechanical components. The direct load connection improves system responsiveness because there is no mechanical slack to take up before motion begins.
This is why frameless torque motors are now widely used in collaborative robot joints, quadruped robot walking joints, and humanoid robot flexible joints. Those applications place a high value on rapid response, low mechanical compliance, and minimal backlash.
A conventional motor-and-gearbox architecture may introduce additional backlash and compliance that engineers must account for during control and mechanical design. The direct-drive approach with a frameless motor simplifies that challenge by removing the gearbox and coupling from the transmission path entirely.
The Integration Problem
Traditional motion systems are assemblies of discrete components: motor, gearbox, encoder, brake, cable harness. Each component comes from a different supplier. Each has its own mounting interface, its own wiring requirements, its own thermal characteristics. The system integrator's job is to make all of these parts work together in a limited space.
This is inefficient. It consumes engineering time, introduces failure points, and limits design flexibility.
Frameless motors shift the integration burden from the system integrator to the motor design itself. The motor is specified to fit within the machine structure. The machine's existing bearings support the rotor. The machine's housing provides the stator mounting. The motor becomes a functional component of the mechanical design rather than an external module that must be accommodated.
The FMK series exemplifies this approach. It is available in eight standard frame sizes, with full customization support for different application requirements. The hollow bore design simplifies cable routing and PCB layout within the joint. The motor is not something you mount; it is something you build around.
The Answer Is Not a Component — It Is an Architecture
The frameless motor does not solve a single problem. It solves a category of problems that all stem from the same root cause: treating the motor as a separate, self-contained module rather than an integrated part of the machine structure.
When you eliminate the housing, you gain space. When you eliminate the shaft and bearings, you save weight. When a frameless motor is paired with a direct-drive architecture, you can eliminate the coupling and gearbox to gain stiffness and reduce backlash. When you eliminate separate mounting interfaces, you simplify integration. Each of these is a distinct engineering benefit, but they all flow from the same design principle — letting the machine itself provide the structure that the motor needs.
We at Kinco have seen this shift across the industry. The FMK series frameless torque motors now serve applications from collaborative robot J1–J6 joints to humanoid robot flexible joints.
The same principle applies whether the motor is 25 mm or 115 mm in diameter — remove what is unnecessary, integrate what remains, and design the motor as part of the mechanical system rather than an add-on module.
That is what frameless motors fix. Not a single problem. A whole way of thinking about motion design.